License #1041772

Work Time

24/7 service

Call Us Today

(855) 999-4417

Blog

12 Common Problems with Frigidaire Furnaces: Troubleshooting Guide

Table of Contents

Frigidaire furnaces are known for their reliability, but like any appliance, they can encounter issues over time. Whether it’s an unusual noise, inconsistent heating, or frequent cycling, these problems can leave you searching for quick fixes. Understanding the root causes of common furnace issues can save you time and help you avoid costly repairs. 

In this troubleshooting guide, we’ll explore 12 common problems with Frigidaire furnaces and provide actionable tips to resolve them, so you can keep your home warm and comfortable throughout the colder months.

1. Furnace Not Turning On

One of the most frustrating issues is when your Frigidaire furnace won’t turn on. This could be due to several reasons:

  • Thermostat Settings: Ensure the thermostat is set to “heat” mode and the temperature is set higher than the current room temperature.
  • Power Issues: Check if the furnace is receiving power. Verify the circuit breaker or fuse box to ensure it hasn’t tripped.
  • Blown Fuse: Inspect the furnace’s internal fuse. If it’s blown, replace it with a new one of the same rating.

Contact an Expert: If troubleshooting doesn’t resolve the issue, consider reaching out to HVAC Alliance Expert for professional furnace repair services to ensure your unit is receiving power properly.

2. Furnace Blowing Cold Air

If your furnace is blowing cold air instead of warm, it may indicate an issue with:

  • Pilot Light: For older models with a standing pilot light, check if it’s out. If so, relight it following the manufacturer’s instructions.
  • Ignitor: In newer models with electronic ignition, a faulty ignitor could prevent the furnace from producing heat.
  • Thermostat Issues: Incorrect thermostat settings can also cause this problem. Make sure the fan setting is on “auto” and not “on,” which can cause continuous blowing of air even when it’s not heated.
  • Call a Professional Technician: A professional from HVAC Alliance Expert can help assess whether it’s the ignitor or another component causing the issue, ensuring your furnace heats efficiently again.

3. Inadequate Heating

If your furnace is running but not providing sufficient heat, the issue could be:

  • Clogged Air Filter: A dirty air filter restricts airflow, reducing the furnace’s efficiency. Replace or clean the filter regularly.
  • Blocked Vents: Ensure that all air vents and registers are open and not obstructed by furniture or other objects.
  • Undersized Furnace: If the furnace is too small for your home’s size, it may struggle to maintain the desired temperature.

Consult a certified technician: If the furnace still struggles to provide enough heat after replacing the filter, scheduling a service with HVAC Alliance Expert can ensure the system is operating at its full capacity.

4. Frequent Cycling

When the furnace turns on and off too frequently, it’s known as short cycling. This can be caused by:

  • Thermostat Placement: If the thermostat is located near a heat source or in direct sunlight, it may cause the furnace to cycle on and off frequently.
  • Clogged Air Filter: Restricted airflow due to a clogged filter can cause overheating, leading to frequent cycling.
  • Oversized Furnace: A furnace that’s too large for your home can heat the space too quickly, resulting in short cycles.

Reach out to a qualified technician for assistance: Short cycling can cause wear and tear on your furnace. Have HVAC Alliance Expert technicians evaluate whether the issue stems from the system’s size or another underlying cause.

5. Strange Noises

Unusual noises coming from the furnace, such as banging, rattling, or squealing, could indicate:

  • Loose Components: Parts like the blower wheel or motor mounts may become loose over time.
  • Ignition Issues: Delayed ignition can cause a loud bang when the gas ignites.
  • Worn Bearings: Squealing noises often indicate worn blower motor bearings.

Contact a skilled technician for expert help: Ignoring unusual furnace noises can lead to more severe issues. A professional from HVAC Alliance Expert can diagnose and fix loose components or worn parts before they worsen.

6. Furnace Not Blowing Air

If the furnace is running but not blowing air, consider these potential causes:

  • Blower Motor: The blower motor may be faulty or have a broken belt. Inspect the motor and belt for wear and replace if necessary.
  • Control Board: The control board regulates the blower motor. If it’s defective, the motor may not receive the signal to operate.
  • Thermostat: A malfunctioning thermostat may not send the signal to the furnace to start the blower.

Get in touch with a professional technician for support: If the blower motor or control board is defective, it’s best to contact a technician from HVAC Alliance Expert to avoid further damage and restore your furnace’s airflow.

7. Pilot Light Keeps Going Out

For furnaces with a pilot light, if it frequently goes out, the causes could include:

  • Dirty Pilot Orifice: Dirt or debris in the pilot orifice can prevent the pilot from staying lit. Cleaning the orifice may resolve the issue.
  • Thermocouple Issues: A faulty thermocouple may not detect the pilot flame, shutting off the gas supply. Replacing the thermocouple is often the solution.
  • Drafts: Drafts or a faulty flue can blow out the pilot light. Ensure proper ventilation and check for drafts around the furnace.

Schedule a visit from a professional technician for help: If cleaning the pilot orifice doesn’t work, let a skilled HVAC Alliance Expert technician inspect and repair the thermocouple or address any ventilation issues.

8. Furnace Leaking Water

A leaking furnace is usually a sign of:

  • Condensate Line Blockage: High-efficiency furnaces produce condensation that drains through a condensate line. If this line is blocked, it can cause water to back up and leak.
  • Broken Condensate Pump: If the furnace uses a condensate pump and it’s malfunctioning, water may not be properly pumped out.
  • Improper Venting: Incorrect venting can lead to condensation forming inside the furnace.

Get in touch with an experienced technician for assistance: A leaking furnace can signal more serious problems. HVAC Alliance Expert can thoroughly check the condensate line and ensure proper venting to prevent future leaks.

9. Faulty Limit Switch

The limit switch monitors the furnace’s temperature. If it’s faulty, it can cause:

  • Overheating: The furnace may overheat if the limit switch isn’t shutting off the burner at the correct temperature.
  • No Heat: Conversely, a faulty limit switch may prevent the furnace from turning on.
  • Frequent Cycling: A malfunctioning limit switch can cause the furnace to turn on and off frequently.

Call for a licensed technician to handle the issue: A faulty limit switch can cause overheating or frequent cycling. Let an experienced HVAC Alliance Expert technician inspect and replace it to keep your furnace running safely.

10. Blower Running Continuously

If the blower runs continuously, it could be due to:

  • Fan Switch: Ensure the fan switch on the thermostat is set to “auto” and not “on.”
  • Limit Switch: A stuck or faulty limit switch can cause the blower to run non-stop.
  • Wiring Issues: Loose or shorted wires in the blower motor circuit can also cause continuous operation.

Book a service appointment with a qualified technician: If the blower continues running even after checking the fan settings, contacting the professionals from HVAC Alliance Expert ensures proper diagnosis and repair of wiring or limit switch issues.

11. Ignition Problems

Ignition issues are common in newer furnaces with electronic ignition systems:

  • Dirty Ignitor: A dirty or cracked ignitor may not spark correctly, preventing the furnace from lighting.
  • Faulty Ignition Control Module: The ignition control module regulates the ignition process. If it’s malfunctioning, the furnace may not ignite.
  • Gas Valve Issues: If the gas valve isn’t opening properly, the furnace won’t ignite.

Seek help from a professional: Ignition issues often require professional intervention. Call HVAC Alliance Expert to inspect the ignitor or gas valve and restore the furnace’s ignition system safely.

12. Error Codes and Lights

Many Frigidaire furnaces are equipped with error codes or lights to indicate problems:

  • Check the User Manual: Refer to the furnace’s user manual for specific error codes and troubleshooting steps.
  • Reset the Furnace: Sometimes, a simple reset can resolve minor errors. Turn off the furnace for a few minutes, then turn it back on.

Call a Professional: If the error code indicates a more serious issue, reaching out to HVAC Alliance Expert for diagnosis and repair is your best option.

Conclusion

Keeping your Frigidaire furnace in top shape is essential for maintaining a warm, comfortable home during the colder months. By understanding and addressing common issues like ignition problems, inadequate heating, or frequent cycling, you can often troubleshoot minor problems yourself. However, for more complex issues, relying on professional help ensures safe and efficient repairs. 

If your furnace troubles persist, don’t hesitate to contact HVAC Alliance Expert for expert assistance. Their certified technicians can diagnose and fix any problem, ensuring your furnace operates reliably when you need it most.

FAQs

Check the thermostat settings and verify if the furnace is receiving power. If these are fine, it’s best to call a certified technician from HVAC Alliance Expert.

Ensure the pilot light is lit, or the ignitor is functioning. If the issue persists, contact HVAC Alliance Expert for professional help.

Replace your furnace filter every 1-3 months, depending on usage and air quality. Regular replacement ensures optimal furnace efficiency.

Frequent cycling may be due to thermostat placement, clogged filters, or an oversized furnace. Contact a technician to inspect the system.

Check for a blocked condensate line, but for more complex issues like a broken pump, it’s best to call HVAC Alliance Expert for expert assistance.

Download MONEY-SAVING HVAC CHECKLIST
Save time and money on your HVAC system
Schedule Your Service!